Computational inelasticity
closest point mappingconsistent stiffness matrixcutting plane algorithmfinite plasticitygeometrically nonlinear theoryhyperelasticityhypoeleasticitylarge deformationlinearizationmaterials of convolution typemultiplicative decompositionoperator splittingradial returnreturn mappingsviscoelasticity
Numerical methods for partial differential equations, initial value and time-dependent initial-boundary value problems (65Mxx) Research exposition (monographs, survey articles) pertaining to mechanics of deformable solids (74-02) Elastic materials (74Bxx) Plastic materials, materials of stress-rate and internal-variable type (74Cxx) Numerical and other methods in solid mechanics (74Sxx)
This book goes back a long way. These words are the first of the preface of this book. Indeed, the scientific community waited many years for this book to be issued. It was announced by the editor since the early nineties of the last century, if the reviewer remembers it well. Of course, the project was mainly delayed because of the sudden dead of Juan Simo in 1994. The manuscript circulated among collegues since 1986, based on course material of the two authors from Stanford University. The main purpose of the book is the numerical computation of elastoplastic problems. These are always nonlinear and are not even continuously differentiable, which causes the main difficulty for the integration. On the other hand, such problems are of supreme importance for many technical applications. So there is a great need for efficient and stable algorithms. The authors enter into this complex field step-by-step and very systematically. They start with the one-dimensional case, which is already difficult enough. Then the authors pass over to the fully three-dimensional case, but first for small deformations. Here they can already demonstrate such usefull algorithms as the return mappings (e.g. the radial return, the closest point mapping, and the cutting plane algorithm). It is well known that the authors contributed a lot of original research work in this field. The operator splitting methodology is described, as well as different linearizations (consistent stiffness matrix). In a third step towards geometrically nonlinear theory, the large deformation continuum mechanics are developed and examplified for elasticity, hyperelasticity, and hypoelasticity. An interesting outline of finite plasticity is then given, mainly based on the multiplicative decomposition. Here, all the aforementioned concepts are again applied. The last chapter on viscoelastic problems completes the book. Again, first the material theory is developed from one dimension to three dimensions, and then the numerical treatment of materials of convolution type is shown. The whole material is presented in a rigorous mathematical format. Domains of functions are precisely introduced, as well as their regularity requirements. Under this aspect, the book is preferable to most other books in the field. Some, not many fully solved examples illustrate the theory. A notation index, however, would have been very helpful for the reader. Many references to other contributions are given, and the discussion of competing theories in finite plasticity shows that this difficult subject is still far from being standard text book knowledge. All in all, the book is an important and valuable contribution to a complicated field, and therefore very recommendable.
- A nonlinear homogenization procedure for periodic masonry
- Macro modelling and homogenization for transformation induced plasticity of a low-alloy steel
- Consistent integration of the constitutive equations of Gurson materials under adiabatic conditions
- Analytical DSA for explicit dynamics of elastic-plastic shells
- Multiscale enrichment based on partition of unity for nonperiodic fields and nonlinear problems
- Mechanics of extended continua: Modeling and simulation of elastic microstretch materials
- Coupled damage-plasticity constitutive model and direct stress interpolation
- Explicit Runge-Kutta methods for the integration of rate-type constitutive equations
- Exact integration of the von Mises elastoplasticity model with combined linear isotropic-kinematic hardening
- Fractional-order relaxation laws in nonlinear viscoelasticity
- A micromechanical basis for partitioning the evolution of grain bridging in brittle materials
- Thermodynamic laws and consistent Eulerian formulation of finite elastoplasticity with thermal effects
- An alternative method for the integration of continuum damage evolution laws
- The equivalence of the radial return and Mendelson methods for integrating the classical plasticity equations
- A small-strain model to simulate the curing of thermosets
- Robust numerical analysis of homogeneous and non-homogeneous deformations
- A plasticity framework for (linear elastic) fracture mechanics
- On the effective behavior of nonlinear inelastic composites. I: Incremental variational principles
- Phenomenological model for the macroscopical material behavior of ferroelectric ceramics
- Convergence of adaptive finite element methods in computational mechanics
- Second-order accurate integration algorithms for von-Mises plasticity with a nonlinear kinematic hardening mechanism
- On standard and vector finite element analysis of a strict anti-plane shear plasticity model with elastic curvature
- A unified stress update algorithm for explicit transient shell dynamics with combined isotropic-kinematic hardening in Eulerian rate-type phenomenological finite elasto-plasticity models
- Modelling the mechanical behaviour of living bony interfaces
- Adaptive FEM analysis of selected elastic-visco-plastic problems
- A discontinuous Galerkin formulation for classical and gradient plasticity. I: Formulation and analysis
- A Newton-Schur alternative to the consistent tangent approach in computational plasticity
- Eigendeformation-based reduced order homogenization for failure analysis of heterogeneous materials
- Efficient and modular algorithms in modeling finite inelastic deformations: objective integration, parameter identification and sub-stepping techniques
- Patient-specific isogeometric fluid-structure interaction analysis of thoracic aortic blood flow due to implantation of the Jarvik 2000 left ventricular assist device
- Functional a posteriori error estimates for incremental models in elasto-plasticity
- Prediction of plastic strain accumulation in continuous fiber reinforced laminates by a constitutive ply model
- An Eulerian multiplicative constitutive model of finite elastoplasticity
- Computational modelling of diarthrodial joints. Physiological, pathological and Pos-surgery simulations
- Associative coupled thermoplasticity at finite strains: Formulation, numerical analysis and implementation
- A nonsmooth Newton method for elastoplastic problems
- A plastic nonlocal damage model
- Frameworks for finite strain viscoelastic-plasticity based on multiplicative decompositions. I: Continuum formulations
- Frameworks for finite strain viscoelastic-plasticity based on multiplicative decompositions. II: Computational aspects
- Anistropic creep modeling based on elastic projection operators with applications to CMSX-4 superalloy
- Energy consistent algorithms for dynamic finite deformation plasticity
- On the numerical integration of three-invariant elastoplastic constitutive models.
- Averaging techniques for reliable a posteriori FE error control in elastoplasticity with hardening
- Algorithmic stabilization of FE analyses of 2D frictional contact problems with large slip.
- Strong coupling methods in multi-phase and multi-scale modeling of inelastic behavior of heterogeneous structures.
- Two-scale kinematics and linearization for simultaneous two-scale analysis of periodic heterogeneous solids at finite strain.
- An efficient time/frequency domain algorithm for modal analysis of non-linear models discretized by the FEM.
- Comparison of plastic, viscoplastic, and creep models when modelling welding and stress relief heat treatment.
- Simulation and interpretation of diffuse mode bifurcation of elastoplastic solids.
- A mortar segment-to-segment contact method for large deformation solid mechanics.
- Thermomechanical model of a continuous casting process
- A formulation of elasticity and viscoelasticity for fibre-reinforced material at small and finite strains
- Finite element procedure for solving contact thermoelastoplastic problems at large strains, normal and high pressures.
- A variational multiscale approach to strain localization -- formulation for multidimensional problems
- Numerical differentiation for local and global tangent operators in computational plasticity
- Finite deformation plasticity based on the additive split of the rate of deformation and hyperelasticity
- Dynamic non-linear stress analysis by the mass matrix BEM
- Continuous and discontinuous Galerkin methods with finite elements in space and time for parallel computing of viscoelastic deformation
- A damage mechanics approach to stress softening and its application to rubber
- An extension of 3-D procedure to large strain analysis of shells
- Runge-Kutta methods in elastoplasticity
- A comparison between the Perzyna viscoplastic model and the consistency viscoplastic model
- A framework for multiplicative associative isotropic elasto-plasticity, that preserves the structure of the infinitesimal theory
- Analysis of nonlinear thermo-viscoelastic-viscoplastic contacts
- Strongly objective numerical implementation and generalization of a unified large inelastic deformation model with a smooth elastic-inelastic transition
- Surface plasticity: theory and computation
- A finite element implementation of the isotropic exponentiated Hencky-logarithmic model and simulation of the eversion of elastic tubes
- A note on stress/strain conjugate pairs: explicit and implicit theories of thermoelasticity for anisotropic materials
- On the use of convected coordinate systems in the mechanics of continuous media derived from a \(\mathbf{QR}\) factorization of \textsf{F}
- Elastoplastic constitutive equation of metals under cyclic loading
- Hencky strain and logarithmic rates in Lagrangian analysis
- Development of a finite strain two-network model for shape memory polymers using QR decomposition
- Modelling multiple cycles of static and dynamic recrystallisation using a fully implicit isotropic material model based on dislocation density
- Multiphase-field model of small strain elasto-plasticity according to the mechanical jump conditions
- Numerical evaluation of discontinuous and nonconforming finite element methods in nonlinear solid mechanics
- Improved integration scheme for the second-order consistent element-free Galerkin method
- New strong formulation for material nonlinear problems based on the particle difference method
- A TFETI domain decomposition solver for elastoplastic problems
- Lubricated elastoplastic contact model for metal forming processes in OpenFOAM
- A solution strategy for non-linear implicit BEM formulation using a unified constitutive modelling framework
- Mathematical homogenization of inelastic dissipative materials: a survey and recent progress
- Meshfree radial point interpolation method for analysis of viscoplastic problems
- Single crystal anisotropy and coupled stability analysis for variant reorientation in Magnetic Shape Memory Alloys
- Benchmark solution of the dynamic response of a spherical shell at finite strain
- Computational formulation for the asymptotic response of elastoplastic solids under cyclic loads
- Finite-strain low order shell using least-squares strains and two-parameter thickness extensibility
- A robust and efficient radial return algorithm based on incremental energy minimization for the 3D Souza-Auricchio model for shape memory alloys
- A limit analysis approach based on Cosserat continuum for the evaluation of the in-plane strength of discrete media: application to masonry
- An adaptive \(h\)-refinement algorithm for local damage models
- An analytical insight into the buckling paradox for circular cylindrical shells under axial and lateral loading
- High-performance model reduction techniques in computational multiscale homogenization
- A weighted Nitsche stabilized method for small-sliding contact on frictional surfaces
- Finite-strain formulation and FE implementation of a constitutive model for powder compaction
- A global-local discontinuous Galerkin finite element for finite-deformation analysis of multilayered shells
- One-dimensional constitutive SMA model with two martensite variants: analytical and numerical solutions
- A comparison of different methods for calculating tangent-stiffness matrices in a massively parallel computational peridynamics code
- A four-point integration scheme with quadratic exactness for three-dimensional element-free Galerkin method based on variationally consistent formulation
- A highly accurate 1st- and 2nd-order differentiation scheme for hyperelastic material models based on hyper-dual numbers
- A coupled Eulerian-Lagrangian extended finite element formulation for simulating large deformations in hyperelastic media with moving free boundaries
- A multiplicative finite element algorithm for the inhomogeneous swelling of polymeric gels
This page was built for publication: Computational inelasticity
Report a bug (only for logged in users!)Click here to report a bug for this page (MaRDI item Q1269440)
